Soundwise.org - Mr PC Pro Cable Mod

Answer and Next Move

Answer and Next Move

Answer

First off, if you look at how wide the cable is and compare it to the tiny screws in the plug that hold it, you should be thinking "no way,,,ain't gonna' fit!"

Second, soldering will make a permanent, and better connection. Simple as that.

Next Move

Prepping the Plug

First, remove those tiny screws with your #1 bit screwdriver.

Clean up the contacts with alcohol, and tin the ends of the contacts, making sure to fill the screw hole with solder.

Quick stop

The plug comes with an insulating sleeve and a tension relief spring. Here's an exploded view of it.

As much as I would have liked to keep the tension relief spring, we just can't due to the thickness of the cable. But there is a plus side, because the new plug is of a much higher quality then the factory plug, it fits in the receiving hole in the speaker, much tighter and makes a better contact. You really have to feel it when you plug it in, it almost feels like it snaps in. And because the speakers and cables really won't be moved much, you won't miss any benefits that the tension relief spring offers.

Now, before you get all excited and think your almost done and want to solder the wires to the plug. Do yourself a favor first, and slip on the outer jacket and insulating sleeve. This will make it a lot easier then trying to slide them the entire length of the cable.

OK, time to solder it.

Use your "third hand" to hold the plug, so you can hold the wire on the contact as you solder. Position the wire under the filled screw hole, place the soldering iron on top of the contact. When you see the solder start to flow, keep an eye on the upper area of the wire. When you see the solder on the wire start to flow, remove the iron, and hold still for a couple of seconds to let the solder start to set. Flip the plug over and do the same procedure for the other contact.

This is optional, but preferred.

Cut a small piece of electrical tape and place it between the two soldered contacts.

This will eliminate any chances of the to soldered wires touching each other.

Now slide the insulating sleeve down, slide the outer jacket down and screw it on.

Guess What!!

Congratulations, your finished!!

Here's a couple of comparison shots between the factory cables and the new ones we just made.

Love that Gold!

New cable looks like it can take on anything.

Well, I hope this has helped some of you, and thanks for stopping by.





Answer and Next Move Answer and Next Move Answer First off, if you look at how wide the cable is and compare it to the tiny screws in the plug that hold it, you should be thinking "no way,,,ain't gonna' fit!" Second, soldering will make a permanent, and better connection. Simple as that. Next Move Prepping the Plug First, remove those tiny screws with your #1 bit screwdriver. Clean up the contacts with alcohol, and tin the ends of the contacts, making sure to fill the screw hole with solder. Quick stop The plug comes with an insulating sleeve and a tension relief spring. Here's an exploded view of it. As much as I would have liked to keep the tension relief spring, we just can't due to the thickness of the cable. But there is a plus side, because the new plug is of a much higher quality then the factory plug, it fits in the receiving hole in the speaker, much tighter and makes a better contact. You really have to feel it when you plug it in, it almost feels like it snaps in. And because the speakers and cables really won't be moved much, you won't miss any benefits that the tension relief spring offers. Now, before you get all excited and think your almost done and want to solder the wires to the plug. Do yourself a favor first, and slip on the outer jacket and insulating sleeve. This will make it a lot easier then trying to slide them the entire length of the cable. OK, time to solder it. Use your "third hand" to hold the plug, so you can hold the wire on the contact as you solder. Position the wire under the filled screw hole, place the soldering iron on top of the contact. When you see the solder start to flow, keep an eye on the upper area of the wire. When you see the solder on the wire start to flow, remove the iron, and hold still for a couple of seconds to let the solder start to set. Flip the plug over and do the same procedure for the other contact. This is optional, but preferred. Cut a small piece of electrical tape and place it between the two soldered contacts. This will eliminate any chances of the to soldered wires touching each other. Now slide the insulating sleeve down, slide the outer jacket down and screw it on. Guess What!! Congratulations, your finished!! Here's a couple of comparison shots between the factory cables and the new ones we just made. Love that Gold! New cable looks like it can take on anything. Well, I hope this has helped some of you, and thanks for stopping by.	Try These Mods! DigitalDiva Floor Stands DigitalDiva Wall Mounts Heresy Speaker Stands LightZ Mr PC Pro Cable Mod